Gilderflukeco BR-ANA Analog Output Smart/Dumb Brick Manuel d'utilisateur télécharger pdf (Page 38)

time is still about 5 seconds. The time the output dwells at each extreme is

about one second.

U) Set Minimum, Maximum and Forced using Keypad:

This is the easiest way to adjust the endpoints of the analog outputs to

prevent a mechanical movement from over traveling. The normal range of

the outputs is 0 to 10 volts DC. If your analog movement is hitting the ends

of travel, you can reduce this range until it doesnʼt hit the mechanical ends of

travel.

Selecting his command redraws the left side of the screen. The drawing

shows the numeric keypad found on most keyboards. The ʻarrowʼ points to

the output which has been selected. You can select a different output by

pressing the ʻN) Nextʼ or ʻL) Lastʼ commands.

Use the ʻ1ʼ, ʻ4ʼ and ʻ7ʼ keys to adjust the ʻminimumʼ position the for the se-

lected analog output. This sets the voltage that will be sent out from the Br-

ANA when you give it a ʻzeroʼ position command through the DMX-512 or

AutoDownload ﬁle. The default analog output (when set to 0/0h) is 0 vdc.

Shows: 8, Ch: 123 @___0, ADL: AutoDownload_Filename

Serial Address- __0

__1 Show_FileName.sho looping @ frame ____1363

inputs: a/green: Y | b/red: Y MSB E minimum maximum "forced" PowerOn

c/blue: Y | d/white: Y address I scale scale position default

minimum maximum "forced" 0 (0) |_|____0__|__255__|_______|____0__|

adjust--> scale scale position-> 1 (1) |_|____0__|__255__|_______|____0__|

|-----------------------| 2 (2) |_|____0__|__255__|_______|____0__|

Up--> | 7 | 8 | 9 | 3 (3) |_|____0__|__255__|_______|____0__|

|-----------------------| 4 (4) |_|____0__|__255__|_______|____0__|

middle--> | 4 | 5 | 6 | 5 (5) |_|____0__|__255__|_______|____0__|

|-----------------------| 6 (6) |_|____0__|__255__|_______|____0__|

Down--> | 1 | 2 | 3 | 7 (7) |_|____0__|__255__|_______|____0__|

|-----------------------| 8 (8) |_|____0__|__255__|_______|____0__|

9 (9) |_|____0__|__255__|_______|____0__|

10 (A) |_|____0__|__255__|_______|____0__|

11 (B) |_|____0__|__255__|_______|____0__|

a) toggle Auto force to 0% or 100% 12 (C) |_|____0__|__255__|_______|____0__|

1, 4, 7, -) sets "forced" to 0% 13 (D) |_|____0__|__255__|_______|____0__|

2, 5, 8, +) sets "forced" to 100% 14 (E) |_|____0__|__255__|_______|____0__|

Hit <CR> to save, <Esc> to bail out 15 (F) |_|____0__|__255__|_______|____0__|

n) Next, l) Last, i) info, o) def., p) looP, h) Halt, r) save, v) Verify, x) Xit

Command-

Gilderﬂuke & Co.• 205 South Flower Street • Burbank, California 91502 • 818/840-9484 • 800/776-5972 • fax 818/840-9485

Br-ANA Manual / December 18, 2012 10:21 AM / page 38 of 60

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 59 60

Pas de commentaire

Gilderflukeco BR-ANA Analog Output Smart/Dumb Brick Manuel d'utilisateur Page 38