Gilderflukeco DMX-512 Input Servo Motor Controller Manuel d'utilisateur

SER-DMXSixteen Channel DMX-512 Input Servo ControllerPrinted April 17, 2001A digital device is either on or off, like a light switch. An analogdevice

D) ServoMotor Power: This screw terminal is used to attach the powersupply that will be running the ServoMotors. The voltage output canbe anywhere fro

I) Feed Forward and Feed Backwards: These connectors on the sidesof the SER-DMX are used to connect adjacent SER-DMXs. These con-nectors should not b

Serial Port Commands:The following commands are used to communicate with SER-DMXsand just about any other piece of equipment manufactured by Gilderf

you are attached to the right serial port. The easiest way to do this is to dis-connect the SER-DMX and short between the Tx data out and Rx data inpi

SER-DMX Configuration:To enter the configuration mode you need to type the following.The (address) is replaced by the HEX value set on the ADDRESS s

In this case the value scale being used is Hex:-Gilderfluke & Company - Sixteen Channel Servo Controller - ver1.04 - c1999 DCM-a) card serial addr

In this case the value scale being used is decimal:-Gilderfluke & Company - Sixteen Channel Servo Controller - ver1.04 - c1999 DCM-a) card serial

If you have selected twelve bits resolution for the outputs, then thevalues will be displayed as follows. Note that addresses that can’t be usedfor t

the Eprom has been protected and warn you that you can no longer makeany changes. Configuration changes can be re-enabled at any time bymoving the jum

for storing the least significant four bits of the next two twelve bit reso-lution channels. Any twelve bit resolution channel that is addressedat an

This page left blankGILDERFLUKE & CO .• 205 SOUTH FLOWER STREET • BURBANK , CALIFORNIA 91502 • 818/840-9484 • 800/776-5972 • FAX 818/840-9485EAST

6) 2-1/2 seconds7) 5 seconds8) 7.5 seconds9) 10 secondsIf any output crosses or reaches the level it is being commandedto, it will drop out of Ease-In

value), ‘4’ (set the value to 50%), and ‘1’ (decrease the value)keys.b) The ‘Maximum Scale’ endpoint is set using the ‘8’ (increase thevalue), ‘5’ (

mum position (100%/255/0FFh). 34) Adjust the first endpoint:a) If you set the movement to the minimum position:Use the ‘1’, ‘4’ and ‘7’ keys on your k

(0%/0/00h). One more press and it will then change to‘n/a’.8) Save your changes: Hitting the <Return>, <Space Bar>or ‘0’ key on your ke

not in use will allow them to cool and extend their lives.c) All=0: Commanding ALL servos to the zero position willstop all pulses being sent to al

n) Test & Adjust Next Output:l) Test & Adjust Last Output: These two commands are used to movethe arrow that shows which output you are adjust

- Decimal to HEXadecimal to ASCII to Percentage -The following chart shows decimal, HEXadecimal, ASCII and a fewpercentage equivalents to aid you w

Overview, continued ... 1Connections, Jumpers and LEDs on the SER-DMX ...

This page is blank so that the text starts on a right pageGILDERFLUKE & CO .• 205 SOUTH FLOWER STREET • BURBANK , CALIFORNIA 91502 • 818/840-9484

Overview, continued:The SER-DMX is used for analog control of remote control-styleServoMotors from a PC•MACs animation control system or anyother de

narrowed down to restrict the movement to a smaller range.When you adjust either end of travel for your ServoMotors, it willnot affect the other endpo

Connections, Jumpers and LEDs on the SER-DMX:A) RS-422 Serial Port: This is used to configure the SER-DMX. Althoughthis connector uses an eight positi

COLOR SIGNAL NAME:LEFT #1 gray - DMX-512 Data Input#2 white (or orange) Signal Ground#3 black - Serial data out from card#4 red + Serial data out from

line with additional SER-DMXs, Digital Audio Repeaters, Smart BrickBrains and other serially controlled devices. The only requirement isthat each unit