Gilderflukeco old Smart Brick Manual Manuel d'utilisateur télécharger pdf (Page 85)

If a single LaserDisk is being used, its frame number must be entered in the LaserDisk first slot.

LaserSearch commands which are located in the MultiDisk Strings will be searched starting with LaserDisk

number seven. Any LaserDisk that has a zero entered will be skipped during MultiDisk searches.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒnÓ Next Entry:

This command is used to switch to the next showÕs setup screen.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒlÓ Last Entry:

This command is used to switch to the last showÕs setup screen.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒkÓ Kopy Another Show:

This command allows you to copy the data found in any other show, and put that data into the

show you are now displaying. As shows are often just about identical except for their start and end

frames, this can save a great deal of time when setting up shows.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒmÓ More.....:

This command allows you to select from the other menus:

1) Main Menu. This brings you back to this menu.

2) Show Setup. This will ask you which of the 255 possible shows you want to modify.

3) String Setup. This allows you to modify the strings used to control LaserDisks.

4) Delay. This allows you to set how long each of the sixteen possible countdown delays are.

5) Schedules. This is where you modify the ninety different possible schedules.

6) Calendar. This is where you select which schedule will be used on any day.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒoÓ Load Defaults:

This command allows you to reload a single show, or all of the shows, with the default configuration

settings shown in the menu above.

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥

ÒxÓ eXit Setup Mode:

This command is used to exit the setup mode. If you hit this command in error, hitting an <ESC>ape

key will get you back to the setup mode. All of the setup commands which don't take effect immediate-

ly, take effect when the eXit command is entered. This includes things like the BAUD RATE, so you will

have to change the baud rate of the terminal you are using at this time.

For compatibility with other products which might be on the same RS-422 serial network, this com-

mand asks you to enter a ÔYÕ or ÔNÕ. This lets them know that the setup mode has been exited on this

card. If you hit this command by mistake, then you can hit the <ESC>ape key to get back to where you

were before.

All other Audio Repeater cards and Brick Brains in the same serial network have their serial ports dis-

abled while any card in the system is in setup mode. This is the only command to which they will re-

spond. After the initial 'X', all of the other cards wait for a 'Y' or 'N' before they will start accepting other

serial commands again. If you find that you are having trouble communicating with any of the cards in

GILDERFLUKE & C

O

.¥ 205 S. FLOWER ST.¥ BURBANK, CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485

75 of 134

Gilderflukeco old Smart Brick Manual Manuel d'utilisateur Page 85