Gilderflukeco old MACs 8 bit Digital Audio System Manuel d'utilisateur télécharger pdf (Page 45)

Smart Digital Audio Repeater Configuration:

Configuration from the Serial Port:

There are two ways to configure a Digital Audio Repeater. The first, and easiest, way of configuring a

Repeater is through the serial port. The second way is through the two 8 position dip switches located on

each card.

To configure the system through the serial port, you need to connect the system just as you do for

any serial communications (see the 'serial commands' section of the manual). The configuration mode

is entered by the command:

"m" (5AA5) (TRACK#)

This command will bring up the following menu from the Repeater which was addressed.

EXAMPLE: to bring up the configuration screen for a card addressed as Ôtrack 00Õ (this is the normal

default configuration address when a Repeater is shipped): m 5 AA5 0 0

This would bring up the following configuration screen (the screen shown is the default

configuration):

a) Channel number- 00 | g) Select from AUX- yes | l) #1 PA station- 01

b) Baud rate- 9600 | h) Direct select- yes | m) #2 PA station- 02

c) Odd parity- no | i) Mute if stopped- no | o) Std PA priorities- no

d) EPROM type- 27C010 | j) Start delay- 0010 | p) Zone Priorities- no

e) Inputs Debounce- 0A | k) Early starts- Jmp Fwd | q) Loop all mode- no

f) DR-400 mode- no | X) exit

1 2 3 4 5 6 7 8

G) Group assignments: | 1 | 0 | 0 | 0 | 0 | 0 | 0 | F |

H) PA Zones Enabled: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 |

I) Half Mute Zones Enabled: |yes|___|___|___|___|___|___|___|

J) Full Mute Zones Enabled: |yes|___|___|___|___|___|___|___|

STOP

INPUT and EDGE HALF MUTE UN STOP RESET START LOOP AT END

K) A input Closing: |______|______|______|______|______|__on__|______|______|

L) A input Opening: |______|______|______|______|______|______|______|______|

M) B input Closing: |______|__on__|______|__on__|______|______|______|______|

O) B input Opening: |______|______|__on__|______|______|______|______|______|

P) PB input Closing: |__on__|______|______|______|__on__|__on__|______|______|

Q) PB input Opening: |______|______|__on__|______|______|______|______|______|

R) Aux input Closing:|______|______|______|______|______|______|__on__|______|

S) Aux input Opening:|______|______|______|______|______|______|______|______|

Enter command- _

The (5AA5) part of the command is a key to keep this mode from being inadvertently entered. The

card addressed by the TRACK# will put a configuration menu on the screen. When this mode is entered

by any card, it disables all of the other serial commands on all the cards in the system. As with the

normal serial command mode, the upper and lower 'case' of all input is important. An 'a' is a command

while an 'A' is a number. All numeric values are entered in HEX (0 - 9, A - F).

If another command is entered while the last command is waiting for additional input, the new

GILDERFLUKE & C

. ¥ 205 SOUTH FLOWER ST. ¥ BURBANK, CALIF. 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485

1 2 ... 40 41 42 43 44 45 46 47 48 49 50 ... 109 110

Commentaires sur ces manuels

Pas de commentaire

Gilderflukeco old MACs 8 bit Digital Audio System Manuel d'utilisateur Page 45

Commentaires sur ces manuels